|
|
ITU mode supports: Denmark Finland Germany Russia (ITU variant) * Hong Kong (ITU variant) South Africa (ITU variant) Korea * Malaysia * Mexico (Telmex and Telnor) * New Zealand * Paraguay Peru Philippines Saudi Arabia Note: All countries listed have been tested in house. Countries marked with a * have also been successfully tested in-country. Mini Q&A ========= Q. What is R2 ? A. R2 is a signaling system (Q.422) used by a number of countries worldwide. This signaling system runs over an E1 Carrier (2.048Mb/s), containing 32 64Kb/s timeslots, of which, 30 timeslots can be used for digital modem calls. Q. Does this feature require new hardware in the 3600? A. No Q. What network modules support this feature? A. All the current 1/2 PRI NMs, including the new 1FE 1/2 PRI NM. Q.Is the Cisco Dial-out Utility supported through an R2 connection? A. Yes. Version 2 of the Cisco Dial-out Utility ( available early November) together with MICA Portware 2.5.1.0 support Dial/Fax out through the R2 interface Q. Is this R2 feature supported the Cisco 2600, 3620, and 3640? A. The ability for Modem calls to be terminated through an R2 interface is available for all platforms that support Cisco digital modems. This current ly limits R2 support to the 3640/3620 Q. Do I need a new version of the digital modem microcode to support R2? A. No. All shipping version s of Portware are supported. For information on Portware and instructions on downloading the latest version , please visit: http://www.cisco.com/public/sw-center/sw-access.shtml. Q. What IOS is required to utilize this feature? A. IOS 12.0(1)T and above Q. Can I support ISDN PRI R2, and CAS in the same chassis? A. Yes, on a per network module basis. Each individual PRI NM can be configured as R2,CAS or ISDN PRI. Q. What countries will this R2 feature be available in? A. At FCS, a subset of the 5300 supported R2 countries will be supported. All Countries in the list above have been successfully tested internally. Q. Will the new mixed media FE/PRI support R2? A. Yes. Q. Can two PRI/R2 links share one DM NM? A. Yes. The pool of modems is available to all R2/PRI interfaces. 99.6>Q: Когда же наконец будет релиз V.90 для MICA ? >A: (Oleg Zharoff) Вышел наконец долгожданный релиз V.90 для MICA модемов, версия 2.5.1.0. http://www.cisco.com/univercd/cc/td/doc/product/access/acs_serv/5300/ mod_info/53fw_pw/53micaa/rn250x.htm 99.7>Q: А вот почему я не могу через console зайти на мою ciscу? И настройки крутил, и порты на машинках живые, а что не так - не пойму. >A: Pavel Stepchenko McFlySr@irc Проверьте марку вашей motherboard. Если это Atrend, проверьте, "родные" ли "косички"? Дело в том, что поганые(кто мне возместит душевное равновесие?! ;) ) китайцы решили, что они умнее всех, и заюзали "косички" с шахматной распайкой(как и на AT486); на остальных же MB - прямая распайка. Если не ATREND - все равно проверьте порты на целостность, так как cu по умолчанию имеет Xon/Xoff и вообще :) Убеждаемся, что на cuaa0(1) не висит (m)getty, пускаем cu -l /dev/ cuaa0(1) , и наслаждаемся жизнью :) Thanks for support: CGHost, Fifo, Jimson, Lee7, Mdh, ReedCat, vul. 99.8>Q: Тут проблема - кто знает как выставить номер сети у Hовелльного клиента ? Hачал бить сетку на VLANы - и возникли проблемы. MS работает нормально, а Hовельный клиент не хочет. >A: (Serge Turchin) Прописать spantree portfast на портах Каталиста. 99.9>Q: Кто-нибудь знает, как быть с утерянным паролем на 1020? >A: (Gleb Pijov) Question: How do you recover lost passwords on a Cisco 1020? Answer: As the Cisco 1020 is rarely physically secured, password recovery is done by calling Cisco and providing a system generated CHALLENGE. Using the override program, the support engineer can provide a one-time password to use to get into enable mode. Then, follow these steps: 1.Customer: Put up dip switch 1 and apply power. You should see "Console Username:". 2.Customer : Login with Username "enable" and Password "override".
|